Skip to content

RAM 2500 Common Problems & Reliability Guide

truck
1994–2026
4 generations23 OBD2 codes22 known problems19 recalls

Get Your FREE AI Diagnostic Report

Enter your year for a personalized diagnosis for your RAM 2500

RAM 2500

No account required · Takes 30 seconds

Overview

The Ram 2500 is the three-quarter-ton heavy duty pickup, sold as the Dodge Ram 2500 until Ram became its own brand around 2010. It comes with single rear wheels only, which separates it from the dually-capable 3500, and it is the base for the Power Wagon off-road trim. Buyers choose between gas V8s and Cummins turbodiesels, and owners search for fixes on front-end shake, diesel fuel system, emissions and transmission trouble. Use this page to match codes and symptoms to the generation and engine you have.

RAM 2500 service intervals, fluids and specs

Quick Summary

Most Common OBD2 Codes

P0300
Common
P0299
Common
P0401
Common

Most Serious Issues

  • Lift Pump and VP44 Injection Pump Failure (24-Valve Cummins)
  • Killer Dowel Pin (24-Valve Cummins)
  • Front End Shake (Death Wobble) and Steering Linkage Wear

19 recalls documented across all generations

By Generation

Available Engines

5.9L Magnum V8
8.0L Magnum V10
5.9L Cummins 12-valve I6 turbodiesel (1994-1998)
5.9L Cummins 24-valve I6 turbodiesel (1998.5-2002)

Common OBD2 Codes

CodeFrequencyNotes
P0300
Common
Random misfire on the 5.9L and 8.0L gas engines is usually traced to worn ignition parts or an intake vacuum leak.
P0171
Occasional
Lean condition on the Magnum gas engines, most often from a vacuum leak at the intake or a dirty mass airflow or MAP sensor.
P0420
Occasional
Catalyst efficiency code on higher-mileage gas trucks. Check for exhaust leaks ahead of the rear oxygen sensor before replacing a converter.
P0335
Occasional
Crankshaft position sensor circuit. On the 24-valve Cummins a failing sensor can cause stalling and no-start, so it gets checked alongside the injection pump.
P0251
Occasional
Injection pump fuel metering fault on the 1998.5-2002 Cummins with the VP44 pump. Low fuel supply pressure from a weak lift pump is a common contributor. Pump timing faults such as P0216 also show up on these trucks.

Known Problems

The 1998.5-2002 Cummins uses a Bosch VP44 rotary injection pump that depends on steady fuel supply pressure from the lift pump. When the lift pump weakens, the VP44 runs short of fuel and can fail. Owners report hard starting, stalling, and sudden loss of power at highway speed, which also takes away power steering and brake assist until the engine is restarted. Many shops replace the lift pump and check supply pressure whenever a VP44 is replaced.

Related codes:P0251

On the 1998.5-2002 5.9L Cummins a steel dowel pin in the front of the block can work loose and fall into the timing gear train. When that happens it can damage the cam, crank and injection pump gears. Mechanics commonly retain or tab the pin whenever the front gear cover is off, and many owners have it done as preventive work.

On manual-transmission trucks with the NV4500, the nut that holds fifth gear on the mainshaft can back off. The truck suddenly drops out of fifth as if shifted to neutral, and continued driving can damage the mainshaft. Rebuild shops sell upgraded nut and gear kits for this transmission. It mostly matters on diesel trucks that tow in overdrive.

The headlight switch and its wiring can overheat and melt on these trucks, which can cut out the headlights or parking lights and in some cases produce smoke under the dash. Owners often replace the switch more than once until the connector and harness are repaired. If the lights flicker or you smell hot plastic near the switch, inspect it before it fails.

Recalls

2000
Steering Wheel Sound Deadener DetachmentNHTSA

Sound deadener material inside the steering wheel could come loose from the cover and housing. Affected trucks were built in 2000 at several Ram assembly plants. The remedy involved the clockspring and steering wheel parts.

Available Engines

5.7L Hemi V8
8.0L Magnum V10 (2003)
5.9L Cummins I6 turbodiesel (2003-2007)
6.7L Cummins I6 turbodiesel (2007.5-2009)

Common OBD2 Codes

CodeFrequencyNotes
P0300
Common
Random misfire on 5.7L Hemi trucks. A ticking or loud lifter noise with a misfire points to valvetrain wear.
P0420
Occasional
Catalyst efficiency code on higher-mileage gas trucks, usually after exhaust manifold or exhaust leaks have been ruled out.
P0299
Common
Turbo underboost on the 2007.5-2009 6.7L Cummins, often from a sticking variable geometry turbo vane or actuator.
P0401
Common
EGR flow insufficient on the 6.7L Cummins. Soot builds up in the EGR valve and passages.
P2002
Occasional
Diesel particulate filter efficiency below threshold on 2007.5-2009 6.7L trucks that see a lot of short trips and idling.
P2463
Occasional
Soot accumulation in the particulate filter on the 6.7L Cummins, typically with failed or interrupted regeneration.

Known Problems

A hard bump at highway speed can set off a violent front-end shake that only stops when you slow down. It is common on 4x4 trucks of this generation and usually comes from worn parts: track bar bushings or mount, tie rod ends, drag link ends, ball joints and wheel bearings, with the steering box mount flexing as well. Chrysler recalled the left tie rod assembly on 2003-2008 4x4 trucks because the ball stud can fracture, and a few owners also report cracked steering box or pitman arm parts. Inspect every steering joint before chasing alignment or tires.

Early 5.9L Cummins trucks lose the fuel lift pump without warning. The engine stalls or loses power at speed, and steering and brake assist go with it. Owners report it between roughly 50,000 and 100,000 miles. Testing fuel supply pressure is the first step when a diesel hesitates or dies.

Typical mileage: 50,000-100,000 miles

Steel brake lines and fittings corrode on these trucks, especially near the fuel tank and rear axle in salt-belt states. Rubber hose crimps have also let go. Owners describe a sudden soft or dropped pedal and fluid on the driveway. Inspect the lines and hoses whenever the truck is on a lift, and replace corroded sections before they leak.

The high-pressure fuel line feeding the number 4 cylinder can crack on 2003-2007 5.9L Cummins engines. Diesel then sprays onto a hot engine and exhaust, and owners have reported smoke and under-hood fires. Replacement lines and line kits are widely sold. A fuel smell, diesel in the engine bay or a sudden loss of power on one cylinder are all reasons to check it.

On 2007.5-2009 trucks with the 6.7L Cummins the EGR cooler can crack and leak coolant into the exhaust path. Signs are unexplained coolant loss, white sweet-smelling exhaust smoke and EGR codes. A recall covered a sagging silencer pad that could contact the cooler on 2007-2008 trucks. Independent shops quote a replacement at about $1,200-$2,000, and dealers charge more.

Related codes:P0401P0404
Shop parts for this repair

The variable geometry turbo on the 6.7L Cummins can stick from soot, and the electronic actuator can fail. Symptoms are weak or inconsistent boost, slow spool, a whistling or grinding noise and limp mode with the check engine light on.

Related codes:P0299

Recalls

2003
Aluminum Wheel CrackingNHTSA

On certain heavy duty pickups the aluminum wheels may have excessive porosity in the center hub area, which can cause a wheel to crack.

2003
Left Tie Rod Assembly FractureNHTSA

The left tie rod assembly may break on 2003-2008 Ram 2500 4x4 trucks, causing a loss of steering control.

2005
Driver Air Bag Inflator RuptureNHTSA

The dual-stage driver frontal air bag can take in moisture over time, which could cause the inflator to rupture on deployment.

2006
ABS Control Unit Brake BalanceNHTSA

On certain pickups with four-wheel ABS, the electronic control unit may cause a loss of front-to-rear brake balance, and the rear brakes could lock up prematurely.

2007
Silencer Pad Contacts EGR Cooler (6.7L Diesel)NHTSA

On 2007-2008 trucks with the 6.7L diesel, a silencer pad can sag and touch the EGR cooler.

2008
Steering Linkage Drag Link FractureNHTSA

On 2008-2009 trucks with Powers and Sons steering linkage, the drag link inner tie rod to pitman arm ball stud may fracture.

Available Engines

5.7L Hemi V8
6.4L Hemi V8 (2014 and later)
6.7L Cummins I6 turbodiesel

Common OBD2 Codes

CodeFrequencyNotes
P0401
Common
EGR flow insufficient on the 6.7L Cummins as soot builds up in the EGR valve. Cleaning intervals are shorter for trucks that idle a lot.
P2002
Occasional
Particulate filter efficiency below threshold on the 6.7L Cummins, often after repeated interrupted regenerations.
P2463
Occasional
Soot accumulation in the diesel particulate filter on the 6.7L Cummins.
P0299
Common
Turbo underboost on the 6.7L Cummins, usually a sticking variable geometry turbo vane or a failing actuator.
P20EE
Occasional
SCR NOx catalyst efficiency code on the 2013 and newer 6.7L trucks with DEF. DEF quality, the NOx sensors and the doser are the usual checks.
P0300
Occasional
Random misfire on the 6.4L Hemi, which is also the symptom owners report when a lifter or camshaft lobe wears.

Known Problems

Soot can make the variable geometry turbo vanes stick, and the electronic actuator on the turbo can fail. The truck loses boost or spools slowly, whistles or grinds, and drops into limp mode. The turbo was revised over the years, so the part number matters when you order a replacement.

Related codes:P0299

The EGR valve can stick or clog with soot, causing rough idle, hesitation and EGR codes, and on 2013 and newer trucks it can send the engine into limp mode. A heavy idling or short-trip duty cycle makes it worse. Cleaning the valve about every 67,500 miles is a common guideline, and sooner for work trucks that idle a lot.

Typical mileage: Cleaning about every 67,500 miles

Related codes:P0401P0404

Short trips and idling keep the exhaust too cool for the filter to regenerate fully, and the filter can plug up. Symptoms include frequent regeneration, lost power and filter codes. Regeneration fuel can also thin the engine oil, so check the oil level and condition if regens are frequent. A replacement filter from the dealer is reported at about $1,500-$2,500, while cleaning costs far less.

Related codes:P2002P2463P244AP244B
Shop parts for this repair

The 68RFE six-speed automatic can shudder at the torque converter and run hot under heavy towing. A failed converter clutch valve can damage the transmission and the converter together, and valve body or clutch pack wear can put the truck in limp mode. Regular fluid service and a transmission temperature gauge are the usual protection for trucks that pull trailers.

Related codes:P0740P0741P0743

The 6.4L Hemi used in 2014 and newer trucks is the subject of owner reports and a class action over valvetrain wear. A persistent tick from the lifters can progress to camshaft lobe wear and misfires, and repairs often mean taking the engine well apart.

The bolt that holds the intake heater grid can work loose on 6.7L Cummins engines. In rare cases this can lead to engine damage, so it is worth having the grid hardware checked, especially on high-mileage trucks.

Recalls

2010
Diesel Fuel Heater Connector OverheatingNHTSA

On 2010-2014 trucks the electrical connectors of the diesel fuel heater may overheat.

2013
Water Pump Coolant Leak (6.7L Cummins)NHTSA

Concentric-brand water pumps on some 2013-2017 6.7L Cummins trucks have no vent hole and may leak coolant.

2014
Front Track Bar Bracket WeldsNHTSA

Inadequate welds on the front track bar frame brackets of 2014 Ram 2500 trucks may allow the bracket to separate from the frame. A similar recall, 16V559000, covers 2015 trucks.

2014
Drag Link Jam Nut LooseningNHTSA

The outboard steering linkage jam nut may loosen and allow one end of the drag link to separate.

2016
ECM Short Circuit Stall (6.7L Cummins)NHTSA

On certain 2016 trucks built in mid-2015 the engine control module may short circuit and stall the engine without warning.

2017
Hydraulic Control Unit FailureNHTSA

The ABS hydraulic control unit may fail, which can disable ABS, electronic stability control and traction control on 2017-2018 trucks.

Available Engines

6.4L Hemi V8
6.7L Cummins I6 turbodiesel
6.7L Cummins High Output I6 turbodiesel

Common OBD2 Codes

CodeFrequencyNotes
P0087
Occasional
Fuel rail pressure too low. On 2019-2020 6.7L Cummins trucks it is a symptom to take seriously because of the Bosch CP4 high-pressure pump issue.
P0299
Occasional
Turbo underboost on the 6.7L Cummins from a sticking turbo vane or actuator.
P2002
Occasional
Particulate filter efficiency below threshold on the 6.7L Cummins.
P2463
Occasional
Particulate filter soot accumulation on the 6.7L Cummins, often seen with interrupted regeneration cycles.
P20EE
Occasional
SCR NOx catalyst efficiency code on trucks with DEF. Frozen or faulty DEF sensors are a reported cause on 2019-2022 trucks.
P0300
Occasional
Random misfire on the 6.4L Hemi, which can follow lifter or camshaft wear.

Known Problems

The Bosch CP4 high-pressure pump on 2019 and 2020 trucks can fail early and spread metal particles through the fuel system, which can stall the engine without warning. NHTSA opened an investigation and Ram recalled the trucks, and the pump went back to the earlier CP3 design for 2021-2024. Metal in the fuel filter, hard starting and low rail pressure are warning signs. If the pump has already shed metal, the repair can include the whole fuel system.

Related codes:P0087
Shop parts for this repair

Diesel trucks with DEF can set emissions faults from clogged EGR valves, frozen DEF sensors, dirty connectors or a worn doser, and the truck can derate if the problem is not fixed. Cleaning the connectors or the doser costs little compared with replacing a DEF pump, which can cost around $1,900.

Related codes:P20EE
Shop parts for this repair

Short trips and long idling can clog the EGR valve and the diesel particulate filter, which shows up as frequent regeneration, rough running and reduced power. A heavy idling duty cycle shortens the cleaning interval.

The 6.4L Hemi has owner reports of a persistent lifter tick that can progress to camshaft wear and misfires, and the engine is named in a class action over valvetrain wear. Repairs often require extensive disassembly.

Trucks with the 68RFE can shudder at the converter or overheat under a heavy trailer. Pressure and heat can also push transmission fluid out of the dipstick tube onto hot parts, which prompted recalls on 2019-2023 trucks.

Related codes:P0740P0741P0743

Soot can stick the variable geometry turbo vanes, and the electronic actuator can fail, leaving the truck with low boost, a check engine light and limp mode.

Related codes:P0299

Recalls

2019
Diesel Fuel Line LeakNHTSA

The fuel lines on certain 2019 diesel trucks may leak fuel into the engine compartment.

2019
Brake Caliper Seal SwellingNHTSA

Brake calipers may have been built with an incorrect assembly fluid that can swell the rubber seals.

2019
High-Pressure Fuel Pump Failure (6.7L Cummins)NHTSA

The high-pressure fuel pump may fail and stall the engine without warning on 2019-2020 trucks.

2019
68RFE Dipstick Tube Fluid LeakNHTSA

Pressure and heat inside the 68RFE transmission may push fluid out of the dipstick tube. A later recall, 22V835000, extends this to 2020-2023 trucks.

2021
Intake Heater Relay Short (6.7L Cummins)NHTSA

An electrical short in the intake heater relay may cause a vehicle fire with the ignition on or off. A related recall, 23V060000, covers 2021-2023 trucks.

2023
Transmission Control Unit WeldNHTSA

An insufficient weld in the transmission control unit can let fluid leak onto electrical parts and cause a loss of drive power.

Need help diagnosing your vehicle?

Get AI Diagnostic Report